• 10m Roll

• Black Finish

• Self-Adhesive Backing

• Non-Slip Stair Edge Profile

• Flexible PVC and Rubber Trim for Tile, Wood and Concrete Steps

Continuous Coverage for Multiple Stair Edges

This black stair nosing trim is supplied as a 10-metre length, allowing it to be measured and divided across several stair treads. It provides a practical way to create a more consistent finish across a complete staircase rather than purchasing a separate pre-cut profile for every individual step.

The number of stairs covered will depend on the width of each tread, the amount required around corners, and the cutting allowance needed during installation. Every step should be measured separately because stair widths can vary, particularly in older properties or staircases that have previously been altered, repaired, or covered with new flooring.

Flexible PVC and Rubber Profile for Step Protection

The trim is described as being manufactured from polyvinyl chloride, rubber, and vinyl rubber. This flexible construction allows the profile to follow a straight stair edge more easily than a rigid metal section, while the black finish creates a neutral appearance alongside a wide range of flooring colours and interior styles.

Its surface is listed as non-slip and is intended to improve traction around the stair edge where footwear regularly makes contact. However, no independent slip-resistance rating or safety certification is included in the supplier information. The profile should therefore be viewed as a practical edging and traction component rather than a guarantee against slipping.

Intended for Tile, Wood and Concrete Steps

Tile, wood, and concrete are listed as the recommended installation surfaces. Each material presents different fitting conditions, so the stair edge should be assessed before the backing is exposed. Smooth tiles may retain cleaning residue, wooden treads may contain polish or loose coatings, and untreated concrete can be porous, dusty, or uneven.

The trim should only be applied to a firm, level, and properly prepared edge. It is not intended to repair cracked concrete, loose tiles, damaged timber, or unstable floor coverings. Any structural or surface problem should be corrected first so that the stair nosing can sit evenly and maintain consistent contact with the receiving surface.

Preparing the Surface for Self-Adhesive Fitting

The product is described as self-adhesive, allowing it to be fitted without beginning with a separate wet adhesive application. Before installation, remove dust, grease, moisture, wax, polish, old adhesive, and loose particles from the stair edge. The surface should be completely dry before the protective backing is removed.

Measure and position the trim without exposing the adhesive first. Once the alignment has been confirmed, peel away the backing gradually while pressing the profile firmly and evenly into place. The item details state that fixings are supplied, but they do not clarify whether this refers only to the adhesive backing or includes additional accessories, so the package contents should be checked before fitting.

Confirming the Profile Measurements Before Cutting

The supplier lists the item dimensions as 10 metres long by 7.5 centimetres wide. A separate specification gives the width as 1.97 inches, which converts to approximately 5 centimetres. These two width measurements do not match and should not be treated as interchangeable when planning a close-fitting stair-edge installation.

An item height of one inch, approximately 25.4mm, is also provided, but it is not explained whether this represents the vertical drop, the overall folded profile, or another measurement. Buyers should confirm the complete profile dimensions before cutting or permanent fitting, particularly where the edging must align with a narrow tread, existing floor covering, or adjoining trim.

Frequently Asked Questions

Is this stair nosing supplied as one continuous 10m roll?

Yes. The product details list a unit count and overall length of 10 metres, with one stair edge trim protector supplied in the pack. A continuous roll can be divided across several steps, but the exact number covered will depend on each tread width, cutting allowance, corner treatment, and any wastage created during fitting.

Can it be fitted to tile, wood and concrete stairs?

Tile, wood and concrete are listed as recommended surfaces. Each surface must still be sound, level, clean, dry, and free from dust, grease, polish, loose coatings, or old adhesive. Porous, uneven, damaged, or contaminated steps may require preparation or a compatible additional fixing method before the trim can be installed securely.

Does the self-adhesive backing remove the need for extra fixings?

The product is described as self-adhesive and the item details state that fixings are supplied, but they do not clarify whether separate screws, plugs, or adhesive accessories are included. Do not assume the backing alone will suit every surface. Check the package contents and assess the stair material, traffic level, and surface condition before installation.

Is the profile definitely 7.5cm wide?

The supplier lists the dimensions as 10m by 7.5cm wide, but a separate specification gives an item width of 1.97 inches, which is approximately 5cm. These measurements do not match. Confirm the selected profile dimensions before ordering, especially where the nosing must fit a narrow tread edge or align closely with existing flooring.

What does the listed one-inch height mean?

The item height is stated as one inch, which is approximately 25.4mm, but the listing does not explain whether this refers to the vertical drop, total folded profile, packaging measurement, or another part of the trim. Compare a confirmed profile drawing or physical measurement with the stair edge before cutting or permanent installation.

Can the vinyl rubber stair edging be cut to size?

Flexible PVC and rubber stair profiles can commonly be divided into individual tread lengths, but the supplier has not provided a specific cutting method. Measure every step separately, mark the trim carefully, and use a suitable sharp tool on a protected surface. Poor cutting can leave uneven edges, reduce adhesion, or affect the finished alignment.

Does the non-slip finish guarantee that stairs will not be slippery?

No. The listed non-slip finish and profile are intended to improve traction at the step edge, but they cannot eliminate every slipping risk. Performance depends on correct fitting, surface cleanliness, moisture, footwear, lighting, and the condition of the staircase. No independent anti-slip test rating or safety certification is included in the supplied details.

At Rubber Fit Floors, we are committed to delivering your orders efficiently and securely to your doorstep. Here’s everything you need to know about our shipping process:

1. Shipping Destinations
We currently ship to the United Kingdom, covering all regions including mainland UK, Northern Ireland, and the Scottish Highlands. If you’re located outside the UK, please get in touch with us to discuss custom shipping options.

2. Processing Time

An order confirmation email does not constitute acceptance of your order. Acceptance occurs only when the order has been dispatched. All orders are processed within 1–2 business days.
Orders placed on weekends or holidays will be processed on the next working day.

3. Delivery Time
Standard Delivery: 3–5 business days.
Express Delivery: 1–2 business days (available at an additional charge).
Delivery times are estimates only and not guaranteed. We are not liable for delays caused by couriers or external factors.

4. Shipping Charges
Standard Delivery: £7.99 (Free for orders over £100).
Express Delivery: £24.95.
For bulky or custom orders, shipping charges will be calculated based on the weight and dimensions of your package.

5. Tracking Your Order
Once your order is dispatched, you will receive an email with a tracking link to monitor your shipment. If you do not receive this information, please contact our support team.

6. Damaged or Lost Shipments
If your order arrives damaged or is delayed beyond the expected delivery time, kindly reach out to us immediately. We will assist you with replacements, refunds, or further inquiries.

7. Contact Us
For any shipping-related questions, feel free to contact our customer support:
📧 Email: procurement@rubberfitfloors.co.uk
📞 Phone: 07404270642
Address: 9 Fiveacre Close, Thornton Heath, CR7 6AS