• 10m Roll

• Two-Tone Finish

• 50mm x 25mm Profile

• Self-Adhesive Vinyl Edging

• Non-Slip Bullnose Stair Trim for Multiple Step Edges

Continuous Edging for Several Stair Treads

This bullnose stair nosing is supplied as a 10m continuous roll, making it practical for staircases where several tread edges need the same style of trim. The longer format allows each section to be measured according to the width of the individual step rather than relying on separate pre-cut profiles. This can support a more consistent appearance across the staircase while reducing unnecessary joins along a single edge. Before cutting or removing the adhesive backing, measure every intended tread separately and calculate the total required length, allowing for any fitting adjustments recommended in the supplied instructions.

A 50mm x 25mm Bullnose Profile

The edging has a listed cross-section of 50mm x 25mm and is described as a bullnose or angle-style stair trim. These dimensions determine how much of the horizontal tread and front stair edge the profile can cover, so they should be checked against the existing staircase before purchase. A correctly sized section should sit evenly without leaving unsupported areas, excessive overhang or a raised corner. The available information does not explain which measurement applies to each side of the angle, so the profile orientation should be confirmed from the physical product or packaging before installation begins.

Grey and Yellow Non-Slip Surface

The trim combines a grey body with a yellow section, creating a noticeable two-tone finish along the stair edge. This contrast can help make the front of the tread easier to identify while giving the staircase a consistent visual border. The product is described as non-slip, but this should not be interpreted as making every staircase completely slip-proof. Grip can still be affected by water, dust, loose debris, unsuitable footwear, worn material or incorrect fitting. Regular cleaning and inspection remain important, particularly on frequently used steps where dirt may collect around the raised bullnose profile.

Surface Preparation for Self-Adhesive Fitting

The vinyl edging is supplied with a self-adhesive backing, allowing it to be installed without visible screw heads across the finished surface. Adhesive performance depends heavily on preparation, so the stair edge should be stable, level, clean and completely dry before fitting. Grease, dust, polish, loose paint and damaged surface material can prevent consistent contact. Each section should be measured, positioned and checked for alignment before the protective backing is removed. Repeatedly lifting and repositioning the trim may weaken the adhesive, so the installation instructions supplied with the product should be followed carefully.

Cutting, Cleaning and Checking the Installed Trim

The 10m roll will normally need to be divided into sections for individual steps, but the source does not specify an approved cutting tool or method. Check the supplied guidance before cutting so the ends remain straight and the material is not stretched or damaged. Once installed, loose grit can be removed with a soft brush, cloth or suitable vacuum attachment. A mild cleaner compatible with vinyl and PVC-rubber materials may be used for routine care, followed by thorough drying. Inspect the ends and adhesive edges periodically for lifting, movement or wear, and correct any loose area before normal stair use continues.

Frequently Asked Questions

What length and profile size does this stair nosing have?

The product is supplied as a 10m continuous roll with a listed bullnose profile of 50mm x 25mm. The roll can provide material for several step edges, depending on the width and number of stairs. Measure each tread individually before ordering or cutting because stair widths can vary, even within the same staircase.

How is the self-adhesive edging installed?

The fitting surface should be firm, level, clean and completely dry before the backing is removed. Measure and position each section first, then press the adhesive side evenly onto the stair edge. Dust, polish, grease, loose coatings and moisture can reduce contact, while repeated repositioning may weaken the adhesive bond.

Can the 10m roll be cut into separate stair lengths?

The roll is intended to provide a continuous supply of edging for multiple sections, but the seller information does not identify an approved cutting method or suitable tool. Check the product instructions before cutting. Each end should remain straight and smooth so it does not lift, curl or create an uneven corner at the stair edge.

Does the yellow and grey finish improve stair visibility?

The contrasting yellow and grey design creates a visually distinct border around the front of the tread, which may make the stair edge easier to recognise against some surrounding floor colours. Actual visibility will depend on lighting, floor finish and colour contrast. The product should not be treated as a certified visibility or accessibility aid unless supporting documentation confirms this.

Does the non-slip surface prevent all slips?

No. The product is described as non-slip, but no stair edging can prevent every possible slip. Water, dust, grease, loose debris, worn material, unsuitable footwear and poor installation can all affect traction. Keep the surface clean, check that the adhesive remains secure and stop using any step where the trim has lifted or moved.

Which stair materials can this edging be fitted onto?

The source confirms a self-adhesive stair trim but does not list specific compatible surfaces such as wood, tile, concrete, laminate or carpet. Adhesive performance varies between materials and finishes, so compatibility should be checked before installation. Avoid applying the strip over loose flooring, crumbling surfaces or heavily textured edges.

What do the 395mm x 248mm x 90mm dimensions represent?

The item details separately list dimensions of 395mm x 248mm x 90mm, while the product itself is described as a 10m roll with a 50mm x 25mm profile. The source does not explain the purpose of the larger figures, so they may relate to the packaged item rather than the fitted trim. This should be confirmed before publishing them as product dimensions.

At Rubber Fit Floors, we are committed to delivering your orders efficiently and securely to your doorstep. Here’s everything you need to know about our shipping process:

1. Shipping Destinations
We currently ship to the United Kingdom, covering all regions including mainland UK, Northern Ireland, and the Scottish Highlands. If you’re located outside the UK, please get in touch with us to discuss custom shipping options.

2. Processing Time

An order confirmation email does not constitute acceptance of your order. Acceptance occurs only when the order has been dispatched. All orders are processed within 1–2 business days.
Orders placed on weekends or holidays will be processed on the next working day.

3. Delivery Time
Standard Delivery: 3–5 business days.
Express Delivery: 1–2 business days (available at an additional charge).
Delivery times are estimates only and not guaranteed. We are not liable for delays caused by couriers or external factors.

4. Shipping Charges
Standard Delivery: £7.99 (Free for orders over £100).
Express Delivery: £24.95.
For bulky or custom orders, shipping charges will be calculated based on the weight and dimensions of your package.

5. Tracking Your Order
Once your order is dispatched, you will receive an email with a tracking link to monitor your shipment. If you do not receive this information, please contact our support team.

6. Damaged or Lost Shipments
If your order arrives damaged or is delayed beyond the expected delivery time, kindly reach out to us immediately. We will assist you with replacements, refunds, or further inquiries.

7. Contact Us
For any shipping-related questions, feel free to contact our customer support:
📧 Email: procurement@rubberfitfloors.co.uk
📞 Phone: 07404270642
Address: 9 Fiveacre Close, Thornton Heath, CR7 6AS