• 9mm Depth

• 900mm Length

• Aluminium Profile

• Self-Adhesive Stair Edging

• Peel-and-Stick Trim for Laminate and Wooden Step Edges

A Slim Finish for Laminate Stair Edges

Exposed laminate and wooden step edges can look unfinished and may become marked through repeated contact. This aluminium stair edging creates a defined transition around the front of the step while helping cover the vulnerable edge of the flooring.

The slim profile is suitable for staircases where a compact trim is preferred over a large stair nosing. Its aluminium construction provides a clean, structured finish that can coordinate with modern laminate and wood-effect flooring.

The profile is supplied in a 900mm, or approximately 3ft, length. Each stair should be measured before ordering because step widths can vary between properties and even across the same staircase.

Understanding the 9mm Profile Depth

The stair edging has an approximate depth of 9mm. This measurement should be compared carefully with the thickness and position of the existing laminate or wooden flooring before installation.

A correctly matched profile should sit neatly around the edge without forcing the floor covering upwards or leaving a noticeable gap. Differences in underlay, flooring thickness and stair construction can affect how the edging fits.

The remaining profile dimensions are not included in the supplied information. Buyers should therefore confirm that the available shape and depth are suitable for their particular stair edge before removing the adhesive backing.

Peel-and-Stick Installation

The profile has a self-adhesive backing, allowing it to be installed by peeling away the protective layer and pressing the trim into position. Separate screws or mechanical fixings are not identified as necessary in the supplied product details.

Before exposing the adhesive, position the profile against the stair edge and check its alignment along the full width. Once the backing has been removed, repeated lifting or repositioning may reduce the quality of the bond.

Apply firm and even pressure across the complete profile after placement. The adhesive should make consistent contact with the prepared surface rather than bridging over gaps, loose flooring or damaged sections.

Preparing Laminate and Wooden Steps

The installation surface should be smooth, clean, dry and structurally secure. Dust, grease, polish, moisture and loose particles can prevent the adhesive from bonding properly to the step.

Laminate boards should be firmly fitted before the trim is applied. The profile should not be used to hold down loose flooring or conceal movement, damaged edges or unresolved structural problems within the staircase.

Highly textured finishes, uneven joints and waxed or contaminated surfaces may require additional preparation. Testing adhesion on a small, inconspicuous section can help assess compatibility before the full profile is installed.

Cleaning and Checking the Installed Trim

Routine cleaning can be completed using a soft cloth and a mild product suitable for aluminium. Loose grit should be removed before wiping because abrasive particles may scratch the visible surface.

Harsh solvents, metal brushes and rough scouring pads should be avoided unless their compatibility with the finish has been confirmed. Excessive water should not be allowed to collect around the profile or enter beneath the laminate edge.

The trim should be inspected periodically for lifting or movement, particularly around the ends. If the adhesive begins to release, the cause should be identified and corrected before the stair continues to receive regular use.

Frequently Asked Questions

What is the length of this aluminium stair edging?

The profile is supplied in a 900mm length, which is approximately 3ft. This may suit many standard domestic stairs, but every step should be measured before ordering. Stair widths can differ slightly, and the profile may require careful trimming where the available space is narrower than 900mm.

How is the stair nosing installed?

The profile has an integrated self-adhesive backing. Installation involves checking the position, peeling away the protective layer and pressing the aluminium trim firmly onto a prepared stair edge. The surface must be clean, dry and smooth because dust, grease or loose material can weaken the adhesive bond.

Are screws or separate fixings required?

The supplied information describes the profile as self-adhesive and instructs the user to peel and stick it into position. Screws or other mechanical fixings are not listed. The trim should therefore only be applied where the adhesive backing can make secure and consistent contact with a compatible surface.

Can it be installed over laminate flooring?

Yes, it is intended for laminate and wood stair edges. The laminate must be firmly secured, level and free from dust, polish and moisture before installation. The trim should not be used to hold down loose boards or hide damaged flooring because movement beneath the profile may cause the adhesive to release.

What does the approximate 9mm depth refer to?

The supplied specifications list the profile depth as approximately 9mm. This should be compared with the flooring thickness and the shape of the intended step edge. The other profile dimensions are not confirmed, so the complete fit should be checked before the adhesive backing is removed.

Can the aluminium profile be shortened?

A 900mm profile may need to be shortened for narrower stairs. Aluminium can generally be cut using suitable equipment, but the exact cutting instructions are not included in the supplied details. Measure carefully, protect the visible finish and ensure that no sharp or uneven edges remain after cutting.

Does this stair edging have an anti-slip surface?

No anti-slip insert, textured tread or tested slip-resistance rating is mentioned in the supplied product information. It should therefore be treated primarily as a finishing and protective stair-edge trim rather than a certified anti-slip product. Secure fitting and routine stair safety remain important.

Is the profile suitable for outdoor steps?

Exterior suitability is not confirmed in the supplied information. It is safest to use the profile on suitable indoor laminate or wooden stair edges unless the manufacturer confirms that the adhesive and aluminium finish can withstand outdoor moisture, temperature changes and weather exposure.

At Rubber Fit Floors, we are committed to delivering your orders efficiently and securely to your doorstep. Here’s everything you need to know about our shipping process:

1. Shipping Destinations
We currently ship to the United Kingdom, covering all regions including mainland UK, Northern Ireland, and the Scottish Highlands. If you’re located outside the UK, please get in touch with us to discuss custom shipping options.

2. Processing Time

An order confirmation email does not constitute acceptance of your order. Acceptance occurs only when the order has been dispatched. All orders are processed within 1–2 business days.
Orders placed on weekends or holidays will be processed on the next working day.

3. Delivery Time
Standard Delivery: 3–5 business days.
Express Delivery: 1–2 business days (available at an additional charge).
Delivery times are estimates only and not guaranteed. We are not liable for delays caused by couriers or external factors.

4. Shipping Charges
Standard Delivery: £7.99 (Free for orders over £100).
Express Delivery: £24.95.
For bulky or custom orders, shipping charges will be calculated based on the weight and dimensions of your package.

5. Tracking Your Order
Once your order is dispatched, you will receive an email with a tracking link to monitor your shipment. If you do not receive this information, please contact our support team.

6. Damaged or Lost Shipments
If your order arrives damaged or is delayed beyond the expected delivery time, kindly reach out to us immediately. We will assist you with replacements, refunds, or further inquiries.

7. Contact Us
For any shipping-related questions, feel free to contact our customer support:
📧 Email: procurement@rubberfitfloors.co.uk
📞 Phone: 07404270642
Address: 9 Fiveacre Close, Thornton Heath, CR7 6AS