A Refined Champagne Profile for Finished Stair Edges

This 1m anodised aluminium stair nosing provides a defined finish around the front edge of a stair tread while helping cover minor imperfections along the fitted area. Its champagne-coloured aluminium profile is combined with two black rubber inserts, creating a clear contrast that suits both modern and traditional staircase finishes.

The 35mm-wide top section provides practical coverage across the tread edge, while the 19.5mm drop extends over the front of the step. This profile should be compared carefully with the staircase dimensions and any installed floor covering before ordering to ensure that it sits correctly without creating an uneven transition.

Supplied with the required screws and plugs, the nosing uses a concealed fixing method. Once installed, the black rubber inserts cover the fixing points, leaving no visible screw heads across the finished aluminium surface.

How the Double Rubber Inserts Support Foot Placement

The two black rubber strips create textured contact areas across the top of the stair nosing. These inserts are intended to improve traction under normal foot traffic and provide a more noticeable surface at the front of the tread.

Because the inserts run along the length of the profile, they provide two separate contact lines rather than relying solely on the smooth aluminium surface. This can be particularly useful on frequently used internal staircases where the leading edge needs a more defined and practical finish.

The inserts should be kept clean and correctly seated within their channels. Dust, loose debris or incorrectly positioned rubber may reduce the consistency of the surface and affect the overall appearance of the installed nosing.

Concealed Fixings for a Cleaner Installation

Visible screws can interrupt the appearance of a decorative stair trim. This nosing is designed so that its fixing points remain beneath the removable rubber inserts, producing a cleaner finish after installation.

The supplied assembly system consists of four screws and plugs. During installation, the rubber strips are removed to expose the pre-existing fixing holes. The profile is then positioned, drilled and secured before the inserts are fitted back into their channels.

This method provides mechanical fixing rather than relying only on adhesive. The suitability of the supplied plugs and screws will depend on the material and condition of the staircase, so alternative fixings may be required for certain substrates.

Understanding the 35 x 19.5mm Stair Profile

The profile measures 35mm across the horizontal tread section and 19.5mm down the vertical face. These measurements determine how much of the stair edge will be covered and should be checked against the existing tread, riser and floor finish.

A profile that is too large may project beyond the intended area, while one that is too small may not conceal the existing edge or imperfections. Measurements should be taken at several points because older stairs are not always completely uniform.

The 1000mm length can be used as supplied where the staircase width matches the profile or cut to the required size using suitable equipment for anodised aluminium. Any cut edge should be finished carefully to remove sharp or uneven sections before fitting.

Protecting and Finishing Worn Stair Edges

Stair edges are exposed to repeated contact and can begin to show chips, marks or uneven finishing over time. An aluminium nosing provides a defined covering around this vulnerable area while helping conceal minor imperfections beneath the fitted profile.

The anodised aluminium construction gives the trim a finished surface and provides a stable structure around the stair edge. The champagne colour offers a softer alternative to standard silver aluminium, while the black inserts create a distinct visual contrast.

The product should not be used to hide serious structural damage, loose stair components or heavily broken edges. Any underlying problem that could affect the stability of the step should be repaired before the nosing is installed.

Installation and Ongoing Care

Before fitting, the staircase surface should be clean, dry and stable. Position the nosing against the tread edge and check that the profile sits evenly along the full width. The fixing points can then be marked through the pre-drilled holes beneath the rubber strips.

Remove the inserts carefully, drill the required holes and secure the profile using appropriate screws and plugs. Once the aluminium section is firmly positioned, press the rubber inserts back into their channels and confirm that they sit flat without raised or loose sections.

Routine cleaning should focus on removing dust and debris from the aluminium and rubber surfaces. A soft cloth and mild cleaning solution can be used where appropriate. Abrasive tools and harsh chemicals should be avoided because they may mark the champagne finish or affect the rubber inserts.

Frequently Asked Questions

What are the exact dimensions of this stair nosing?

The nosing measures 1000mm in overall length, with a 35mm horizontal section across the top of the tread and a 19.5mm vertical section covering the front edge. These dimensions should be compared with the staircase and installed flooring before purchase, as profile compatibility depends on the actual tread shape and finished floor height.

How do the concealed fixings work?

The screw holes are positioned beneath the two removable black rubber inserts. During fitting, the inserts are lifted out, allowing the aluminium profile to be drilled and screwed into position through the existing holes. Once the profile is secure, the rubber strips are returned to their channels, covering the screws and producing a cleaner finished appearance.

Are the screws and plugs included with the stair nosing?

Yes, the product is supplied with four screws and plugs for installation. However, the correct fixing type can depend on whether the staircase is made from concrete, timber or another material. The supplied components should be checked against the substrate before installation, and suitable alternatives should be used where the original fixings are not appropriate.

Can the 1m aluminium profile be cut to a smaller size?

The aluminium profile may be cut where a staircase is narrower than 1000mm, provided suitable aluminium-cutting equipment is used. Measurements should be checked carefully before cutting because removed material cannot be restored. The cut edge should also be smoothed and finished properly so that no sharp or uneven section remains after installation.

Do the black rubber inserts make the stairs completely slip-proof?

The two rubber inserts are intended to improve surface traction and provide defined contact areas across the front of the tread. They should not be treated as a guarantee against every slip because performance can be affected by footwear, moisture, contamination and installation quality. Keeping the inserts clean and securely seated supports more consistent use.

Can this nosing cover damaged or uneven stair edges?

The 35 x 19.5mm profile can cover minor marks, worn finishes and small imperfections within the area beneath the trim. It should not be used as a substitute for repairing loose, cracked or structurally damaged steps. The supporting surface must remain stable enough to hold the screws securely and support the profile during repeated foot traffic.

Is this stair nosing suitable for concrete steps?

It may be fitted to prepared concrete steps when appropriate drilling equipment and compatible plugs are used. The substrate should be sound, level and free from loose material before installation. Because concrete strength and condition can vary, the supplied plugs should be checked for suitability rather than being assumed appropriate for every concrete staircase.

How should the aluminium and rubber sections be cleaned?

Loose dust can be removed with a soft brush or cloth, followed by a mild cleaning solution where required. Strong solvents, abrasive pads and aggressive chemicals should be avoided because they may mark the anodised champagne finish or affect the rubber strips. Any moisture left around the inserts should be wiped away after cleaning.

At Rubber Fit Floors, we are committed to delivering your orders efficiently and securely to your doorstep. Here’s everything you need to know about our shipping process:

1. Shipping Destinations
We currently ship to the United Kingdom, covering all regions including mainland UK, Northern Ireland, and the Scottish Highlands. If you’re located outside the UK, please get in touch with us to discuss custom shipping options.

2. Processing Time

An order confirmation email does not constitute acceptance of your order. Acceptance occurs only when the order has been dispatched. All orders are processed within 1–2 business days.
Orders placed on weekends or holidays will be processed on the next working day.

3. Delivery Time
Standard Delivery: 3–5 business days.
Express Delivery: 1–2 business days (available at an additional charge).
Delivery times are estimates only and not guaranteed. We are not liable for delays caused by couriers or external factors.

4. Shipping Charges
Standard Delivery: £7.99 (Free for orders over £100).
Express Delivery: £24.95.
For bulky or custom orders, shipping charges will be calculated based on the weight and dimensions of your package.

5. Tracking Your Order
Once your order is dispatched, you will receive an email with a tracking link to monitor your shipment. If you do not receive this information, please contact our support team.

6. Damaged or Lost Shipments
If your order arrives damaged or is delayed beyond the expected delivery time, kindly reach out to us immediately. We will assist you with replacements, refunds, or further inquiries.

7. Contact Us
For any shipping-related questions, feel free to contact our customer support:
📧 Email: procurement@rubberfitfloors.co.uk
📞 Phone: 07404270642
Address: 9 Fiveacre Close, Thornton Heath, CR7 6AS